A truly fully loaded pump package and MCC building; this unit ran for just under a year (Red Earth) before the formation failed and it was moved off site. Designed for 1500# and full sour operation, the W130M Triplex pumps have full duplex stainless fluid ends and all piping and valves are internally coated. On the discharge side, a lot of the control valves, transmitters etc. were removed when it arrived, however, all missing parts have now been replaced with new. On the suction side, the filters and charge pumps were removed, which is good because now there is a dance floor size spot where we can outfit the suction end exactly how you require. A generous electrical wiring package is also included with everything wired to JB’s and the “as new” MCC building.
Video Walkthrough #1: On-site Tour
You’re not going to want to miss this tour the current crown jewel of current surplus pump package inventory!
Video Walkthrough #2: Optional Configuration for Charge Pump(s) & Filter(s)
Watch this quick video to see how this dual injection pump building is already configured for a single charge pump, a double charge pump, a single filter, or a double filter. You can read more about this configuration by reading our Surplus Spotlight post for this 200 hp Sour Dual Injection Pump Building.
Adjacent 800 AMP MCC Building with PLC
View full details of this MCC Building on its listing page.
360º Virtual Tour
Explore this package in rich detail through a virtual walkthrough below.
View the adjacent 800 AMP MCC Building with PLC:
Main Pumps, Motors & Assemblies
Triplex Pumps:
Two (2) Weatherford W130M Triplex Pumps
Duplex Stainless Fluid Ends
Client choice of plungers
Maximum Continuous RPM Rating: 450RPM
3” RJ Suction, 1.5” FF Discharge Connections
Rated for 130HP Continuous Duty
Sheave Kit and V-Belt Drive
Aluminum Belt Guards
3 Feed Lubricators w/ 55 Gal Oil Reservoir
Suction & Discharge 600cu In Stabilizers
Mounted on sub assemblies and attached to main skid
Pump Notes
Pumps are in excellent condition as verified by our own internal inspection and our commitment to a 12 month warranty. The internal inspection is available for review by interested parties.
The package ran for just under one year prior to shutdown
Pump Performance
Triplex Pump Motors:
Two (2) TECO Westinghouse 100 HP Electric Motors
TEFC; 1200RPM
VFD Rated, Constant torque
480/3/60VAC
Instrumentation
PI-1110/1210 Discharge pressure Indicator (0-3000 PSI)
PIT-1100/1200 Rosemount 3051 Discharge Transmitters
FQIT/FE-1000 1 ½ x 2 EZ-IN (2” 1500# RF) Turbine Flow Meter w/ MC-III Analyzer
VSH-1100/1200 High Vibration Switch
LSL-1100/1200 Murphy EX Low Oil Level Shutdown
LSH Sealed Sump Level Switch
PDIT Rosemount 3051 Filter Differential Transmitter
Suction Instrumentation will be selected once customer decides configuration of filters/charge pump etc. or it can be taken to site and completed there.
Piping
Suction Piping:
6” 150# Suction Inlet
Remainder for Suction Piping 3″ & 6″ to Each Pump
3″ Spools for Stabilizer Mounting
Internally Coated
Drain Piping
All process piping drains go to sealed sump via threaded drain piping
Filter drain piping currently in place (absent of filters)
Pump stuffing boxes drain into open Sump
Discharge Piping
Each individual discharge line exits the plunger pump into a 2” 1500 ANSI rated line. The discharge stabilizers are located directly after the plunger pump discharge.
The PSV and automated startup bypass valve are located before the discharge header. There will also be a block and check valve prior to connecting to the discharge header from each pump individual discharge line, to prevent back flow possibilities.
After the two discharge lines connect, there is the meter run with an uninterrupted 10 x upstream / 5 x downstream flow criteria.
After the meter run, the flow flows through a 3” check and a ball valve, before leaving to skid edge.
PSV and start-up bypass piping go back to main pump suction
Drain valves to drain sump
Internally Coated
All supports are mounted on structural skid members
All supports are secured by clamp style tie-downs
Floating Full Port Block Valves on the system to ensure an adequate flow rating of the line/system.
Skid
17’ W x 39’ L Skid and Building
¼” Checker Plate Flooring
2” Drip Lip Around Skid
Two (2) Open Sumps /
One (1) Sealed Sump w/ 2″ Vented Outside
Sump: High Level Sump Switch
Building
Gable Style Building
Ice Rakes
Four (4) 12” x 18” Louvers w/ closers
One (1) Double Man Door
One (1) Single Man Door
3” Fire Retardant Spray Foam Under skid Insulation Insulated Skid
Electrical
Six (6) Interior Lights w/ Switches
Two (2) Exterior Lights w/ Switches
One (1) High Mount Exhaust Fan w/ switch
One (1) Low Mount Exhaust Fan w/ switch
LEL and H2S Gas Detection
One (1) 120V Electrical Receptacle
Two (2) ESD Buttons
Two (2) Hazlok XP heaters w/ thermostats
All electrical has been tested and replaced as required. New junction boxes have been installed.
End Devices Connected to JBs
Two (2) pressure transmitters (PIT-1100/1200) – Suction
One (1) differential pressure transmitter (DPIT-1000) – Suction
Two (2) pressure transmitters (PIT-1110/1210) – Discharge
Two (2) vibration switch (VSH-1100/1200)
Two (2) oil level switch low (LSLL-1100/1200)
One (1) flow meter 4-20 connection (FE/FT-1000)
One (1) sump level switch (LSH-1300)
Included: Rigid aluminum conduit and steel unistrut used throughout
Lamicoids for all switches, junction box’s, and ESD’s
Equipment Overview
View Virtual Tour
View Video Walkthroughs
Pump Performance
PDF Feature Sheet
Unbranded Feature Sheet
View Drawings
